ELECTRONIC MEASUREMENT EQUIPMENT MECHANIC INSPECTOR Job in Keesler AFB, Mississippi – Department of the Air Force

0

jobs

The United States government is a massive employer, and is always looking for qualified candidates to fill a wide variety of open employment positions in locations across the country. Below you’ll find a Qualification Summary for an active, open job listing from the Department of the Air Force. The opening is for an ELECTRONIC MEASUREMENT EQUIPMENT MECHANIC INSPECTOR in Keesler AFB, Mississippi Feel free to browse this and any other job listings and reach out to us with any questions!

ELECTRONIC MEASUREMENT EQUIPMENT MECHANIC INSPECTOR – Keesler AFB, Mississippi
Air Education and Training Command, Department of the Air Force
Job ID: 278839
Start Date: 06/15/2020
End Date: 07/07/2020

Qualification Summary
This is a Temporary position Not to Exceed 12 months. In order to qualify, you must meet the general experience requirements described in the Office of Personnel Management (OPM) Qualification Standards Handbook X-118C. QUALIFICATIONS: Applicants will be rated in accordance with the OPM Qualification Standard Handbook X-118C for the WG-2600, Electronic Equipment Installation And Maintenance Family. Although a specific length of time and experience is not required for most blue-collar positions, you must meet any screen-out element listed, and show through experience and training that you possess the quality level of knowledge and skill necessary to perform the duties of the position at the level for which you are applying. Qualification requirements emphasis is on the quality of experience, not necessarily the length of time. The screen out element for this position is ability to perform the work as a ELECTRONIC MEASUREMENT EQUIPMENT MECHANIC INSPECTOR without more than normal supervision. Physical Effort Frequently lifts and carries, unassisted, items weighing up to 40 pounds. Sometimes required to lift and carry items weighing more than 40 pounds with the help of weight handling equipment or assistance from other workers. The work requires working in a sitting position for extended periods of time, and frequent standing, walking, bending, crouching, reaching, a stooping are required. Some work may require the aid of magnifying lenses, eye loops, and microscopes to accomplish repairs on miniature components. Working Conditions Employee typically works in well-lighted, heated and ventilated areas. May be required to work at remote user locations under variable conditions or within clean room environments where special garments including head covering, shoe covering, and gloves are required. Exposed to the possibility of electronic shock, burns from electrical or RF energy or hot solder, and cuts and bruises. JOB ELEMENTS: Your qualifications will be evaluated on the basis of your level of knowledge, skills, abilities and/or competencies in the following areas: 1. Knowledge of operating electronic principle involved in the production and utilization of oscillations over a broad range of frequencies, signal and waveform behavior, distortion, and amplification, pulse, trigger, and synchronization techniques, a variety of display and indication methods, the make-up, operation, and use of variety of equipment such as microwave equipment radar and missile test consoles, high frequency sampling and storage oscilloscopes, distortion analyzers, recording oscillographs, and digital delay generators, and the methods and techniques of precise measurement of electrical and electronic quantities and relationships such as standing wave ratio, power, impedance, reactance, and attenuation. 2. Knowledge of safety regulat10ns and procedures. 3. Skill in tracing signals and voltage paths, and m the analysis of waveform characteristics such as timing,duration, frequency, and phasing, and test set-ups to isolate malfunct10ns and check performance characteristics of special or unique test panels or mockups. 4. Skill using and maintaining hand tools such as drills, chassis punches, wrenches, soldering irons, and Micro-soldering units to remove and replace circuit parts. 5. Ability to apply a variety of difficult techniques to inspect complicated repair, modification, testing, alignment, and calibration of equipment, which serve as test equipment or precision measurement standards. 6. Ability to use computer terminals to maintain records and document actions. PART-TIME OR UNPAID EXPERIENCE: Credit will be given for appropriate unpaid and or part-time work. You must clearly identify the duties and responsibilities in each position held and the total number of hours per week. VOLUNTEER WORK EXPERIENCE: Refers to paid and unpaid experience, including volunteer work done through National Service Programs (i.e., Peace Corps, AmeriCorps) and other organizations (e.g., professional; philanthropic; religious; spiritual; community; student and social). Volunteer work helps build critical competencies, knowledge and skills that can provide valuable training and experience that translates directly to paid employment.You will receive credit for all qualifying experience, including volunteer experience.

If you’d like to submit a resume or apply for this position, please contact Premier Veterans at abjobs@premierveterans.com. All are free to apply!

Apply

Post a job on LemonWire. Email jobs@lemonwire.com.
Want to advertise on listings like this? Email ads@lemonwire.com.

Advertisements

Leave a Reply

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.